AZ Ultra Vans
← All posts

Blog · Nov 15, 2026 · 14 min read · Johnathon Lawson

Van electrical system sizing: batteries, solar, inverter and alternator charging without the guesswork

Total your daily amp-hours, then size the lithium bank, solar, DC-DC charger and inverter. Includes a worked example, 12V vs 24V vs 48V and 2026 part prices.

On this page
  1. Step 1: Total your daily amp-hours
  2. Step 2: Size the lithium bank
  3. Step 3: Size the solar
  4. Step 4: Size alternator charging (DC-DC charger)
  5. Step 5: Size the inverter
  6. 12V vs 24V vs 48V
  7. Wire and fuse basics (general, not instructions)
  8. Typical 2026 component costs
  9. FAQ

Van electrical systems usually go wrong in one of two ways. Some builders buy a big kit first and find out later whether it matches how they live. Others guess low and wake up to a flat bank on the second cloudy morning. The fix for both is the same: list every load and how long it runs, total it in amp-hours, then size each part from that number.

This guide walks through that process with a worked example, then covers the lithium bank, solar, alternator charging, the inverter, 12V vs 24V vs 48V and 2026 part prices. It is a planning guide, not wiring instructions. Wiring mistakes in a vehicle start fires. Follow each component's installation manual, ABYC E-11 (the marine DC standard most van builders use) and RVIA practice, and hire a qualified installer or licensed electrician for anything you are unsure of, especially the 120-volt side.

Step 1: Total your daily amp-hours

An amp-hour (Ah) is one amp drawn for one hour, and batteries are sold in amp-hours, so that is the easiest unit to plan in. Multiply each device's draw in amps by its hours of use per day. If you only know watts, divide by 12 for a 12-volt system. Lithium actually sits nearer 12.8 V, so dividing by 12 errs on the safe side.

Three rules keep the estimate honest:

  • Use real duty cycles. A compressor fridge does not run all day, but in Arizona heat it runs far more than the brochure suggests.
  • Add inverter losses. Victron's sizing method adds 15% to AC loads on inverters under 1,000 W and 10% on larger ones (Victron knowledge article).
  • Round up, both the load and the number of days you want to last.

Worked example: a two-person weekend and remote-work van

This table is built from published specs, not measured in a real van. Rows marked "est." use our own estimates.

LoadDraw (12V)Summer hoursSummer Ah/dayWinter hoursWinter Ah/day
Compressor fridge, 45 L class~1.25 A summer / ~0.6 A winter (est.)24302414
Roof fan, mid speed~2 A81612
LED lighting~2 A48612
Water pump~5 A (est.)0.52.50.52.5
Diesel heater, electrical only~1.5 A avg00812
Starlink Mini, direct 12V~2.5 A (30 W)615615
Laptop on the inverter, 60 W + 15%~5.75 A529529
Phones, watch, headlamps (USB)~0.8 A32.532.5
Total103 Ah89 Ah

Where the numbers come from:

  • Fridge. Dometic's spec for the CFX3 45, as retailers reproduce it, is about 1.03 Ah per hour at 12V, tested at 90°F ambient with a 39°F interior (retailer spec listing). That is roughly 25 Ah a day. A van sitting in a 105°F Phoenix afternoon is hotter than that test, so we used 30 Ah for summer. Our van kitchen guide covers fridge choice and placement.
  • Roof fan. Retailer Q&As put MaxxFan top speed at roughly 4.25 to 5 A (etrailer). We used 2 A for a middle setting.
  • Diesel heater. The battery only runs the fan, pump and controller, which guides put at roughly 10 to 30 W once it is running. The glow plug pulls more for a few minutes at startup.
  • Starlink Mini. Distributors and independent testers report about 20 to 40 W on average. Powering it straight from 12V avoids the inverter loss.

So the design number is about 105 Ah a day, or roughly 1,350 watt-hours. An induction cooktop changes that fast. One 1,800 W burner for 15 minutes is 450 Wh, plus 10% inverter loss, or about 41 Ah per meal. Cooking is the decision to settle first, because it drives the bank, the inverter and the cable size.

Step 2: Size the lithium bank

Victron's method uses three numbers: daily use, days of autonomy and usable capacity (Victron). For days of autonomy, it suggests 1 day if you drive daily with a DC-DC charger, at least 2 if solar is your main source, and 3 for full-time, winter or bad-weather use. Its example counts lithium iron phosphate (LiFePO4) as about 80% usable and lead-acid as 50%. That is why a lithium bank is sized at about 125% of your usable need, while lead-acid needs double.

Use patternUsable Ah neededRated lithium bank (÷ 0.8)Practical choice
Driving most days, DC-DC charging105131200 Ah
Weekend trips, solar as main source210263300 Ah
Full-time, winter, cloudy stretches315394400 Ah

That matches what owners report. One Van Living Forum member found that 400 W of solar and 200 Ah of lithium ran a 12V fridge, lights, a small TV and a low-power laptop with plenty to spare in summer (thread). His list had no induction cooking and no air conditioning.

Battery points that matter in Arizona:

  • Heat is the bigger risk. Manuals differ on the charging range. Lifeline lists -4°F to 113°F, LiTime 32°F to 122°F, and EPEVER's LFP units up to 131°F. A closed van in a July parking lot can beat all of those. Mount the bank low, inside the insulated cabin and out of direct sun, and check your battery's high-temperature cutoff.
  • Cold matters on trips north. Most LiFePO4 must not be charged below 32°F. For winter trips to Flagstaff or the White Mountains, choose a self-heated battery or a charger and BMS that block cold charging.
  • Match the batteries. Victron advises against mixing chemistries, ages or brands in one bank.
  • Count the weight. A Battle Born 100 Ah battery weighs 31 lb and measures 12.76 x 6.86 x 8.95 in (Battle Born). Three of them weigh 93 lb before cable and brackets. See our weight and payload guide.

A 12V 100Ah LiFePO4 battery with low-temperature protection is the usual building block. Add a battery monitor such as the Victron SmartShunt 500A, so that after two weeks you can swap the estimates in your table for measured numbers.

Step 3: Size the solar

Solar has to replace what you use, in the sun you actually get. Solar sites that draw on NREL data put Phoenix at roughly 6 peak sun hours a day on average, from about 8 in June to under 5 in December. NREL's free PVWatts calculator gives monthly figures for your exact location.

Flat-mounted van panels deal with shade from racks and fans and lose output in heat. We use a 0.7 loss factor for all of that, which is a planning estimate rather than a manufacturer figure.

Solar watts needed = daily watt-hours ÷ (peak sun hours x 0.7)

  • 1,350 Wh, average Arizona sun (6 hours): about 320 W.
  • 1,350 Wh, December (about 4.5 hours): about 430 W.

So 400 W covers this van for most of the Arizona year, and 600 W adds margin. Roof space is usually the limit. A rigid Renogy 200 W panel measures 58.7 x 27.5 x 1.38 in and weighs about 26.5 lb, according to Renogy and its dealers. Three of them need about 83 in of roof length side by side, plus clearance around the fan. Our Sprinter vs Transit vs ProMaster comparison has the roof measurements.

Size the MPPT charge controller by its output current. 400 W ÷ 14 V is about 29 A, so a 30 A unit such as the Victron SmartSolar MPPT 100/30 fits. 600 W needs a 50 A controller. If you wire panels in series, check the controller's input voltage limit against the panels' cold-morning open-circuit voltage, as its manual explains. Rigid 200 W 12V monocrystalline panels weigh more than flexible ones but generally cope better with roof heat.

Step 4: Size alternator charging (DC-DC charger)

In a van that moves most days, the alternator is the most dependable charger, working at night, under monsoon clouds and in winter. With a modern smart alternator and a lithium house bank, a DC-DC charger goes between the starter side and the house bank. It caps the current, applies a lithium charge profile and protects the van's own battery.

Check what the van can supply first:

  • Ford Transit. Vanlife Outfitters says a 250 A alternator is standard from 2020 on. It suggests using no more than about half the rating, or about 100 A. The upfitter connection points are fused at 60 A (CCP1, always on) and 175 A (CCP2, which the van can switch off) (Vanlife Outfitters). FarOutRide notes that CCP2 shuts off 30 to 75 minutes after the engine stops (FarOutRide). Ford's body and equipment manual for your model year is the final word, and Ford asks upfitters to consult its Body Builder Advisory Service before changing the charging system.
  • Ram ProMaster. Spec listings show a 220 A alternator. Ram offers no factory second alternator, so higher-output setups use aftermarket kits.
  • Mercedes Sprinter. Sources disagree on factory output by engine and year, so check your build sheet and Mercedes' body builder guidelines.

The common choice is a 50 A unit such as the Victron Orion XS 12/12-50A. Victron lists 50 A output, up to 98.5% efficiency and a 9 to 17 V input (Victron technical data). The Arizona-relevant line is that it derates 1.5% for every °C above 40°C (104°F). Mounted beside a hot engine bay, it will deliver less than 50 A in summer, so give it airflow.

At 50 A, our 105 Ah day comes back in a little over two hours of driving. A 300 Ah bank charging up from 20% takes about five. Vanlife Outfitters describes paralleling two Orion XS units on the Transit's CCP2 for about 100 A, which suits big banks if the van's documentation allows it. On any van, wire the charger's engine-run input as its manual describes, so it cannot drain the starter battery while parked.

Step 5: Size the inverter

Size the inverter for the AC loads you run at the same time, plus their startup surge. Larger inverters draw more power at idle and need heavier cable and bigger fuses.

What you plug inTypical sizeExample, 2026 listed priceDC draw at full output (12V)
Laptops, camera and e-bike chargers500 to 1,200 VAVictron Phoenix 12/1200, $279.65, 2,200 W peak (NAZ Solar Electric)~100 A
Above, plus blender or coffee maker2,000 VA2,000 VA inverter/charger~180 A
Induction, microwave, shore charging3,000 VAVictron MultiPlus-II 12/3000/120-50, $999.62, 120 A charger, 41.9 lb (NAZ Solar Electric)~250+ A

The last column explains why smaller is easier. Running 3,000 W from a 12V bank means about 250 A, which needs very heavy cable, short runs, a lithium-rated main fuse and a battery BMS that allows that discharge rate. If you only charge laptops, a Victron Phoenix 12/1200 is cheaper, lighter and much simpler to install safely.

Air conditioning is the special case. A 12V unit skips the inverter, but its daily amp-hours can exceed everything in our table combined. See our heating and cooling guide.

12V vs 24V vs 48V

Higher voltage moves the same power with less current, so the cables can be thinner. The catch is that nearly every van appliance is 12V. FarOutRide priced complete systems side by side and found that 24V was not automatically cheaper. It also concluded that 48V is hard to justify in a camper van (FarOutRide).

12V24V48V
FarOutRide's rangeUp to ~1,450 W solar and 3,000 W inverter (2,000 W with air conditioning)Up to ~2,900 W solar and ~5,000 W inverterNot recommended for vans
Cable4/0 AWG handles a 3,000 W inverter4/0 handles ~5,000 W. 2/0 can replace 4/0 at 3,000 WThinnest, but fewer fuses and breakers are rated for it
AppliancesFans, pumps, fridges and lights connect directlyNeeds a 24-to-12V converter and two DC panelsConverter needed for nearly everything
Alternator chargingSimple 12-to-12 DC-DCNeeds a 12-to-24V step-up chargerFew options

At around 105 Ah a day, 12V is the right answer. Move to 24V only when your load table calls for an inverter over 3,000 W or more than about 1,500 W of solar.

Wire and fuse basics (general, not instructions)

This section explains the ideas so you can read a diagram and talk to an installer. It does not replace the manuals, ABYC E-11, RVIA practice or a qualified electrician.

  • The fuse protects the wire. Each fuse or breaker is sized so its wire cannot overheat, and it sits as close to the power source as the standard and manual require. A lithium bank's main positive needs a fuse with a high interrupt rating, which is why Class T is common. A Blue Sea Class T fuse block is a typical example.
  • Size wire for heat and voltage drop. ABYC E-11 allows 3% voltage drop on circuits that need steady power, such as main feeders and electronics, and 10% on general lighting. Measure the full round trip, positive plus negative (ABYC). If the ampacity and voltage-drop tables disagree, use the larger size. Blue Sea publishes a free wire sizing chart.
  • Use the right materials. That means fine-strand tinned marine battery cable, lugs matched to the cable, a hydraulic lug crimper, heat shrink, and grommets wherever cable passes through metal. Secure every run against vibration.
  • Secure batteries for a crash. Use a solid mount, not a strap to plywood.
  • Treat 120V as a separate job. Shore inlets, outlets, GFCI protection and transfer switching follow the RV rules RVIA builders use, NFPA 1192 and NEC Article 551. Hand this part to a licensed electrician.
  • Measure instead of guessing. A DC clamp meter checks real current without disconnecting anything.

Victron's free book Wiring Unlimited explains cable and fuse principles in plain language.

Typical 2026 component costs

These are US retailer listings from November 2026, with a link wherever we opened the page. Lines marked "estimate" are our own ranges. Prices move often, and none of these are AZ Ultra Vans prices.

ComponentExample2026 listed price
12V 100 Ah LiFePO4, premiumBattle Born BB10012$799 sale, $949 regular (Battle Born)
12V ~200 Ah LiFePO4, value brandsSOK 206 Ah and similar~$400 to $950
12V 300 Ah LiFePO4Epoch Essential Series~$1,199
DC-DC charger, 50 AVictron Orion XS 12/12-50A~$328 ($386 list)
Solar charge controller, 30 AVictron SmartSolar MPPT 100/30~$112 to $140
Rigid solar panel, 200 WRenogy 200 W 12V mono~$162 to $170
Battery monitorVictron SmartShunt 500A~$100 to $111
Inverter, 1,200 VAVictron Phoenix 12/1200$279.65
Inverter/charger, 3,000 VAVictron MultiPlus-II 12/3000$999.62
Main fuseBlue Sea Class T block, 225 to 400 A~$80 to $141, plus ~$52 to $64 per fuse
Cable, lugs, bus bars, breakers, DC panelVaries with layout~$400 to $1,000 (estimate)

For the example van (200 to 300 Ah, 400 W solar, 50 A DC-DC, 1,200 VA inverter), we estimate parts at about $2,500 to $4,500, depending mostly on the battery brand. As a cross-check, FarOutRide's itemized 12V system with two 100 Ah batteries, 360 W of solar and a 1,000 W inverter came to $4,696. A 400 Ah, induction-ready 3,000 VA system costs well beyond that, and installation is extra. For the full build budget, see how much a van conversion costs in 2026.

FAQ

How many amp-hours does a typical van use per day?

It depends mostly on the fridge, remote work and cooking. Our example came to about 90 to 105 Ah. Induction cooking or 12V air conditioning can double that. A battery monitor will show your real number within a couple of weeks.

Is 200 Ah of lithium enough for a van?

For a van that drives most days with a DC-DC charger and about 400 W of solar, usually yes. For full-time off-grid camping, winter trips or induction cooking, plan on 300 to 400 Ah.

Do I need a DC-DC charger, or can I use a battery isolator?

With lithium and a modern smart alternator, a DC-DC charger is the safer and more common choice, because it limits alternator load and charges with the right profile. Use the connection points in your van maker's body builder documentation.

How much solar fits on a van roof?

Three 200 W rigid panels at 58.7 x 27.5 in each take about 83 in of roof length side by side. Many long high-roof vans fit 400 to 600 W around a roof fan. Measure your own roof first.

What size inverter do I need?

Size it for the AC devices you run at the same time, plus their startup surge. Laptops fit a 1,200 VA unit. Induction or a microwave usually means 2,000 to 3,000 VA, with much heavier cable.

Should I build a 24V system?

Only if your loads call for an inverter over about 3,000 W or more than about 1,500 W of solar. Below that, most van gear is 12V and 24V saves little.

Can I wire my van myself?

Many owners do the low-voltage DC work themselves, following every manufacturer manual and ABYC E-11 practice and having the work inspected. Shore power and 120V wiring belong with a licensed electrician. If any connection leaves you unsure, stop and call a qualified installer.

Some links are Amazon affiliate links. As an Amazon Associate we earn from qualifying purchases, at no extra cost to you.

← All posts