AZ Ultra Vans
← All posts

Blog · Nov 15, 2026 · 14 min read · Johnathon Lawson

Van build materials and weight: plywood vs 80/20, countertops, and the payload math most builders skip

Pounds per square foot for plywood, MDF, butcher block and stone, 80/20 vs wood framing, rivnuts and plusnuts, a worked payload budget and how to weigh your van.

On this page
  1. The three numbers on your door jamb
  2. What sheet goods weigh
  3. Countertops: why stone is a mistake
  4. 80/20 aluminum vs wood framing
  5. Fastening into van ribs: rivnuts, plusnuts and the rest
  6. A worked payload budget
  7. How to weigh your van
  8. FAQ

Every van build has a weight budget, whether or not the builder writes it down. The van's maker sets it with the GVWR, the gross vehicle weight rating on the driver's door jamb label. Everything counts against it: plywood, batteries, water, the dog and the two people in the front seats.

Most builders choose materials by look and price and only think about weight once the van feels soft over speed bumps. This guide starts with what materials weigh, compares aluminum extrusion with wood, covers fastening to thin van ribs, runs a full payload budget for a two-person build, and ends with the number that settles it: a scale ticket.

Sourced figures are linked, our own math is labeled, and prices were checked in November 2026.

The three numbers on your door jamb

Before materials, know what you are budgeting against:

  • GVWR: the most the loaded van may weigh, people and fuel included.
  • GAWR front and rear: the most each axle may carry. The two axle ratings usually add up to more than the GVWR, so you can't max out both at once.
  • Curb weight: the empty van. Payload is GVWR minus curb weight.

Brochure payload figures are for a base van. Our Sprinter vs Transit vs ProMaster comparison lists manufacturer maximums from about 3,450 lb (Sprinter 2500 High Roof 170 AWD) to 4,320 lb (ProMaster 3500 159 Extended). Options, AWD, a diesel, a partition or a heavier trim all lower those numbers. The van in your driveway is the one that matters.

A real example: the Far Out Ride build team published the numbers for their second Transit, a T-350 AWD high roof on the 148 in extended body. It weighed 6,030 lb empty against a 9,500 lb GVWR, which leaves 3,470 lb. Its axle ratings are 4,630 lb front and 5,660 lb rear. We use that van for the budget below because it is a real, weighed starting point.

What sheet goods weigh

Plywood is most of the visible weight in a typical build: subfloor, wall and ceiling panels, cabinet boxes, the bed deck. Thickness matters more than species, but species still matters.

Our math in the table starts from published densities. Wikipedia's plywood article puts birch plywood at about 680 kg/m³ and softwood (conifer) plywood at 460 to 520 kg/m³. The MDF article gives a typical 600 to 800 kg/m³. Baltic birch is sold in metric thicknesses (6, 12 and 18 mm), so those rows use the real thickness. Softwood ply and MDF rows use nominal inches and the middle of each density range.

Sheet goodThicknesslb per sq ft4 x 8 sheet (lb)
Baltic birch6 mm (about 1/4 in)0.8427
Baltic birch12 mm (about 1/2 in)1.6753
Baltic birch18 mm (about 3/4 in)2.5180
Softwood plywood (pine/fir)1/4 in0.6420
Softwood plywood (pine/fir)1/2 in1.2741
Softwood plywood (pine/fir)3/4 in1.9161
MDF1/2 in1.8258
MDF3/4 in2.7387

Our estimates from the densities above. A specific sheet can vary by 10 percent or more with moisture and glue content. Many Baltic birch sheets come 5 x 5 ft (25 sq ft), so a 12 mm sheet of that size is about 42 lb.

What that means in a van:

  • Cabinet boxes in 1/2 in (12 mm) ply are the sweet spot for most builders. They hold screws well and weigh two thirds as much as 3/4 in. Far Out Ride builds its frameless galley cabinets in 12 mm Baltic birch (sink cabinet build).
  • 3/4 in ply belongs where it carries load: a bed deck with a long span, a seat base, or a countertop substrate. It does not belong in drawer sides or cabinet backs.
  • Wall and ceiling panels in 1/4 in or 6 mm ply are plenty. Panels carry almost no load. They hang from furring or rivnuts.
  • Skip MDF in a van. It is the heaviest board on the list, it swells when wet, and van interiors get condensation.
  • Poplar-core plywood is a lighter cabinet option. Solid poplar averages 29 lb per cubic foot (Wood Database), well under birch. Weigh a sheet at the yard to be sure.

The floor is a good reality check. Far Out Ride's documented floor (1 in XPS foam board, 1/2 in birch plywood and sheet vinyl over a Transit cargo floor) weighs 200 lb in total (floor build). That is before a single cabinet goes in.

Countertops: why stone is a mistake

A kitchen counter at home can be granite because the house doesn't move. In a van, the counter sits around 36 in off the floor, takes vibration all day, and adds weight that never pays for itself. Here is what a common galley top weighs, 60 in long by 22 in deep (about 9.2 sq ft) with no sink cutout:

MaterialThicknesslb per sq ft60 x 22 in top (lb)
Softwood plywood, finished or laminated3/4 in1.918
Baltic birch, oiled18 mm2.523
MDF with laminate3/4 in2.7+25+
Hard maple butcher block1 in3.734
Hard maple butcher block1-1/2 in5.550
Granite2 cm11.1101
Granite3 cm16.6152
Engineered quartz (estimate)3 cm13 to 17120 to 155

Our math. Hard maple averages 44 lb per cubic foot (Wood Database). Granite runs 2.65 to 2.75 g/cm³, or 165 to 172 lb per cubic foot (Wikipedia). Quartz varies by brand, so use the maker's spec sheet.

A 3 cm granite top weighs about three times a thick maple butcher block and six times a plywood top. That weight sits high, where it hurts handling more than a water tank on the floor, and slab stone doesn't like flexing on a cabinet that racks over washboard roads. Engineered quartz brings one more problem. It is about 90 percent silica by weight, and cutting it raises a well-documented silicosis risk for fabricators (Wikipedia: engineered stone). Never cut it yourself in a driveway.

What builders use instead:

  • Hardwood butcher block, 1 to 1-1/2 in. It can be sanded back; seal the end grain and sink cutout well. A hard maple butcher block countertop finished with pure tung oil is a common pick.
  • Bamboo ply or Baltic birch, oiled. Far Out Ride's second van uses 3/4 in bamboo ply for the counter and backsplash (sink cabinet build).
  • Plywood with high-pressure laminate, the light, cheap route RV makers have used for decades.

80/20 aluminum vs wood framing

T-slot aluminum extrusion, usually sold as 80/20 after the best-known maker, shows up in a lot of premium builds: bed frames, cabinet skeletons, garage shelving. It is often sold as "the lightweight option." That's only partly true. Per foot of the same outside size, it weighs about what wood does.

Framing memberOutside sizelb per ftPrice per ft (Nov 2026)
80/20 10101 x 1 in0.51$5.40
80/20 10201 x 2 in0.92$9.60
80/20 1515-LITE1.5 x 1.5 in1.05$9.96
80/20 15151.5 x 1.5 in1.35$11.76
Douglas fir 2x21.5 x 1.5 in actual0.50lumberyard price, not checked
Douglas fir 2x31.5 x 2.5 in actual0.83lumberyard price, not checked
Fir 1x3 furring strip0.75 x 2.5 in actual0.42lumberyard price, not checked

80/20 weights and per-inch prices from the 8020.net product pages for 1010, 1020, 1515-LITE and 1515, which also list a $3.00 cut charge. Wood weights are our math from Douglas fir's average dried weight of 32 lb per cubic foot (Wood Database).

So why does aluminum often end up lighter in a finished build? Because it is far stiffer and stronger than wood of the same size, so you use less of it, in thinner panels with fewer members. The Far Out Ride team built their second van's bed frame in 1515-LITE with a 3/8 in plywood deck. The whole bed weighs 90 lb (45 lb of aluminum, 45 lb of plywood) and cost $765 in parts (bed platform build). On their weight page, they say the van could have been lighter with 80/20 for the cabinets too, but they chose wood for full-time living.

Pick 80/20 for an adjustable bed height, long spans that carry big loads, or parts you can unbolt and reuse. A 1515 lite T-slot extrusion bundle plus T-slot corner brackets and drop-in T-nuts makes a bed frame straightforward. Pick wood when budget matters or the part is a box the plywood itself stiffens, which covers most cabinets. A common middle path: aluminum for the bed, plywood boxes for the galley and closets.

Fastening into van ribs: rivnuts, plusnuts and the rest

Cargo van walls and ceilings are thin sheet steel with a network of ribs and factory holes. You don't screw cabinets into the outer skin. You fasten to the ribs and pillars, and most builders do it with threaded inserts.

Rivnuts (rivet nuts). A threaded insert that you push into a drilled hole and squeeze with a setter tool. The back of the insert collapses and clamps the sheet, leaving a machine-screw thread you can use over and over. Common van sizes are M6, M8, 1/4-20 and 5/16-18. Far Out Ride's documented builds show the details that matter:

  • The bed frame uses 16 rivnuts in 5/16-18, in holes drilled to 7/16 in (bed platform).
  • The ceiling frames hang on M6 and M8 rivnuts set with an Astro 1442 setter. They use transfer screws to mark matching holes in the wood, and a tap to clean the threads so screws don't bind and spin the insert (ceiling build).
  • The wall cabinet bolts to M6 rivnuts with spacers between cabinet and wall, so tightening the screw doesn't pull the rivnut through the sheet (sink cabinet).

A decent rivet nut setter kit with M6, M8, 1/4-20 and 5/16-18 mandrels and a box of stainless or zinc rivnuts cover most builds. Add a set of transfer screws to mark the matching holes in wood and a step drill bit set for clean holes in sheet metal.

Plusnuts. A slotted blind nut whose body folds into a wide bulb behind the sheet instead of a thin collar. That spreads the load over more metal and copes better with thin or slightly oversize holes. They need a bigger hole than a rivnut of the same thread, so they suit spots that take repeated or pulling loads, like a seat base anchor point. Plusnut-style blind nuts and their setters are sold separately from rivnut kits, so check the tool before you buy.

Habits that prevent most fastener failures:

  • Use factory holes where you can, and match each insert's grip range to the sheet thickness.
  • Look behind before you drill. Wiring, fuel and brake lines and curtain airbags can run behind panels. Your maker's body builder guide shows where drilling is allowed: Ford BBAS, the Mercedes-Benz body builder portal or Ram's body builder site.
  • Prime every drilled edge so it doesn't rust under the panel. A self-etching primer is the usual fix.
  • Don't over-torque. A spinning rivnut is a pain to remove.
  • Heavy and crash-critical items get through-bolts and backing plates: seat bases, battery boxes, water tanks. Seats with belts are a job for a qualified upfitter using crash-rated parts.

A worked payload budget

Here is a realistic two-person build on the Far Out Ride T-350 AWD (3,470 lb available). Rows with a link or a named source are measured or published. Rows marked "est." are our planning estimates.

ItemlbBasis
Floor: 1 in XPS, 1/2 in birch, vinyl200Far Out Ride, measured
Insulation, about 225 sq ft of Thinsulate32Our insulation guide's math
Wall and ceiling panels, 6 mm ply, furring, fasteners180est. (about 180 sq ft at 0.84 lb plus framing)
Bed, 80/20 1515-LITE and 3/8 in ply90Far Out Ride, measured
Galley and cabinets, 12 mm ply150est. (one 41 in flat-pack galley is 113 lb)
Countertop, 1-1/2 in maple, 60 x 22 in50Table above
12V compressor fridge45est.
Three 100 Ah lithium batteries93Battle Born, 31 lb each
3,000 VA inverter/charger42Victron MultiPlus-II listing
DC-DC charger, wire, fuses, bus bars40est.
Three 200 W rigid solar panels80Renogy, about 26.5 lb each
Roof rack and ladder95Far Out Ride
Roof fan and diesel heater36Far Out Ride (20 + 16)
Composting toilet23Nature's Head spec
Mattress and bedding50est.
Build subtotal1,206
Fresh water, 25 gal at 8.3 lb/gal, plus tank228est. tank 20 lb
Two adults340est.
Food, clothes, kitchen, tools, chairs, recovery gear300est.
Trip-ready total2,074
Margin left on 3,470 lb1,396

Component weights come from our electrical, kitchen and bathroom guides, which link each listing.

That looks comfortable, and for this plan it is. Now make the choices people make on social media. Swap in a 3 cm granite top (+102 lb). Build every cabinet in 3/4 in ply (+150 lb, est.). Carry 40 gallons of water (+125 lb). Add a fourth battery (+31 lb), a wet bath (+150 lb at the low end of one builder's 150 to 400 lb range) and a rooftop air conditioner (about +77 lb). Load 200 lb of bikes, boards and coolers in the garage. Now the trip-ready van carries about 2,909 lb, and the margin is down to roughly 560 lb. That is before a third passenger, a dog, a hitch rack or a full grey tank.

This isn't hypothetical. The same team reported that their first Transit, a 148 in high roof with a 9,000 lb GVWR, came out at about 8,950 lb fully loaded, roughly 50 lb under the limit (Far Out Ride).

Watch the rear axle, not just the total. A garage full of gear, water at the back doors and a hitch bike rack all load the rear axle, so a van can sit under its GVWR and still be over its rear GAWR. Keep batteries and water low and between the axles. Air springs and helper springs can level a sagging van, but they don't raise any rating.

If you are still choosing a floor plan, our 12 best layouts with measurements marks the plans that push water and weight to the rear. For what each system costs as well as what it weighs, see how much a van conversion costs in 2026.

How to weigh your van

Spreadsheets are estimates. A scale ticket isn't. Most truck stops have a certified multi-platform scale, and CAT Scale is the largest network.

What it costs. CAT Scale's FAQ lists a full-price weigh at $15.25 and a reweigh at $5.25, if it's the same vehicle at the same scale within 24 hours and you show the first ticket (CAT Scale FAQ). The network weighs vehicles from 2,000 to 200,000 lb, so any cargo van qualifies.

How to do it. CAT's how-to-weigh page tells motorhomes and straight trucks to put the front axle on platform 1 and the rear axle on platform 2, with the whole vehicle on the scale. Weigh the van the same way. Your ticket shows the front axle, rear axle and gross weight. It doesn't show individual wheels or corners, because CAT scales don't weigh that way.

When to weigh.

  1. Before the build, empty, with a full tank and just the driver. This is your true curb weight, and it is often heavier than the brochure.
  2. After the build, with tanks empty. This tells you what the conversion really weighs.
  3. Trip-ready, with full water, everyone aboard and all the gear. This is the ticket to compare with the door-jamb GVWR and both GAWRs.

The second ticket minus the first is the conversion's real weight. For components, a digital hanging scale or a bathroom scale lets you weigh cabinets and gear bins before they go in, so the spreadsheet matches reality.

Truck-stop scales won't show side-to-side balance, so spread the battery bank and water tank left and right rather than stacking them on one side.

FAQ

How much payload does a camper van conversion usually use? In our worked example, about 1,200 lb for the build and 2,100 lb trip-ready. Heavy materials and a wet bath push that toward 2,900 lb.

Is 3/4 in plywood overkill for van cabinets? Usually, yes. 12 mm (1/2 in) Baltic birch holds screws well and weighs about a third less. Save 3/4 in for bed decks, seat bases and counter substrates.

Is 80/20 lighter than wood? Not foot for foot. A 1 x 1 in 80/20 1010 weighs about the same as a fir 2x2. It ends up lighter in a finished build because you need fewer, smaller members, and it costs much more.

Can I use a quartz or granite countertop in a van? You can, but a 60 in top in 3 cm stone weighs about 120 to 155 lb, against about 50 lb for thick maple butcher block. It also sits high and doesn't like flexing on a moving cabinet. Most builders regret the weight.

Rivnuts or plusnuts? Rivnuts for most furniture, panels and brackets. Plusnuts where you want more bearing area or the hole is thin or slightly oversize. Anything heavy or crash-critical also gets through-bolts with backing plates.

Do air bags or helper springs increase my payload? No. They can level the ride, but the GVWR and axle ratings on the door label don't change.

Where can I weigh my van, and what does it cost? At a CAT Scale or similar certified scale at a truck stop. CAT's FAQ lists $15.25 for a weigh and $5.25 for a same-day reweigh at the same scale. Weigh it empty, after the build, and fully loaded.

Some links are Amazon affiliate links. As an Amazon Associate we earn from qualifying purchases, at no extra cost to you.

← All posts