On this page
- The short answer
- The numbers side by side
- Moisture and condensation: the part that actually matters
- Weight: what each approach adds to your payload
- Cost per van in 2026
- How much interior width each approach costs
- Install difficulty and time
- Sound deadening: a separate job
- Reflectix, radiant barriers and the Arizona question
- What experienced builders recommend, and regret
- A simple decision guide
- FAQ
Insulation is the part of a van build nobody photographs and everybody argues about. It goes in early, disappears behind panels, and if it is wrong you may find out years later when a panel comes off and the steel behind it is orange.
This guide compares the four approaches most people actually choose between: 3M Thinsulate, sheep's wool batts (mostly Havelock), rigid foam board (polyiso and XPS) and spray foam. For each: R-value per inch, moisture behaviour, weight, 2026 cost for a typical high-roof van, install difficulty and interior width lost. Where sources disagree, and they often do, we say so.
The short answer
- Thinsulate is the default for a reason: hydrophobic, light, quiet, easy and removable. It is also the priciest per square foot of the "stuff it in the cavity" options.
- Wool is a little warmer per inch, a little cheaper, and handles moisture by buffering it rather than shedding it. It is heavier and messier to install.
- Foam board gives the most R per dollar and is the floor standard, but it is a poor fit for curved van walls and can create hidden water traps if the gaps behind it are not sealed.
- Spray foam has the highest R per inch and doubles as an air seal, but it is permanent, it can trap water against steel if applied badly, and some body shops do not want to repair panels that have it.
Most experienced builders end up mixing: foam board on the floor, Thinsulate or wool in the walls and ceiling, and butyl sound deadener on the big flat panels before any of it goes in.
The numbers side by side
These are published or retailer-listed figures. Lab R-values are a best case; ribs, fasteners and seams in a steel van bridge heat around every insulation type, a point Vansmith's Transit insulation guide makes clearly.
| Material | R per inch (published) | Typical van thickness | Weight | Moisture behaviour |
|---|---|---|---|---|
| 3M Thinsulate SM600L | about 3.1 to 3.3 (some sellers claim 5.45) | about 1.65 in (42 mm) | about 0.14 lb per sq ft | Hydrophobic synthetic fibres, does not hold water |
| Havelock wool batt | 3.6 | 2 in (R7 or R8 batt) | about 20 lb per 100 sq ft box (R7) | Hygroscopic: absorbs and releases vapour |
| Polyiso board | 5.6 at 75°F, about 5.0 at 15°F | 1 in | about 5.4 to 6.9 lb per 4x8 sheet | Foil faced, vapour-closed |
| XPS board (Foamular 150) | 5.0 | 1 in | estimate 4 to 7.5 lb per 4x8 sheet | Vapour-closed, holds R better in cold |
| Closed-cell spray foam | 6.5 to 7 | 0.75 to 2 in | about 0.15 lb per sq ft per inch (1.75 pcf kit) | Air and vapour barrier when continuous |
Sources: Thinsulate thickness and basis weight (672 g/m²) come from 3M's SM600L technical data sheet. The per-inch figures for Thinsulate, polyiso, XPS and spray foam are from Far Out Ride's insulation guide; Campervan HQ lists Thinsulate at 5.45 per inch, which does not square with a roughly R5.2 product about 1.65 inches thick. Wool figures are Havelock's. Polyiso weights are from DuPont Thermax data and a Lowe's Johns Manville listing; the XPS and spray foam weights are our math from typical density and the Froth-Pak kit's 1.75 lb per cubic foot.
Two things stand out. Per inch, Thinsulate and wool are close. And polyiso loses R-value in the cold, exactly when you want it, which is why Far Out Ride and others use XPS on the floor.
Moisture and condensation: the part that actually matters
Every lived-in van makes water. Breathing and sweating overnight add it, cooking adds more, and an unvented propane heater adds a lot more. When that warm, damp air touches cold sheet metal, it condenses. The question is where the water ends up.
There are two schools of thought.
Vapour-open (breathable). Use hydrophobic or hygroscopic fill (Thinsulate, wool), skip a plastic vapour barrier, and give the cavity a way to dry. Far Out Ride argues that moist air will inevitably reach cold steel somewhere, so a breathable wall that can dry is safer than trying to seal it perfectly. The Wayward Home, who used Havelock wool in a Sprinter 144, also skipped a vapour barrier on the logic that wool takes up vapour and releases it as humidity drops.
Sealed. Put a continuous vapour-closed layer against the steel (closed-cell spray foam, or foam board with every seam taped and every gap foamed) so warm interior air never reaches the metal. Vansmith suggests this mainly for cold-climate builds, with careful drainage.
The failure mode people regret is the half-and-half build: a "sealed" layer that is not actually sealed. Foam board glued to a ribbed, curved wall leaves air gaps behind it; a forum warning that gets repeated a lot is that those gaps on irregular van surfaces become water traps. Spray foam that pulls away from flexing panels can do the same. On r/vandwellers and the Ford Transit forums, the recurring rust stories are about water trapped behind foam that nobody could see, found years later when a panel came off. Commenters in those same threads point out that thousands of foamed vans are fine, and that the problem is trapped condensation, not foam as such. Open-cell foam is the one product nearly everyone warns against, because it holds water.
A second regret pattern shows up in a r/vandwellers thread on rockwool: commenters argue van walls flex and rattle constantly, so any assembly that depends on a perfect seal against the steel will eventually develop gaps.
Practical rules that most of these sources agree on:
- Clean, dry and treat any surface rust before anything covers it. Spray foam over rust seals the rust in.
- Keep factory drain holes and weep holes open. Do not foam them shut.
- Pick one strategy per wall. Breathable fill plus a partial seal is the worst of both.
- Ventilate. A roof fan cracked open overnight does more for condensation than any insulation choice.
- Measure. A cheap digital hygrometer on the wall tells you whether your van is running at 45 percent humidity or 80.
Weight: what each approach adds to your payload
For a high-roof Sprinter 144 or Transit 148, Campervan HQ suggests roughly 40 to 45 linear feet of 60-inch Thinsulate for walls, ceiling and doors, which is about 200 to 225 square feet. Havelock recommended about 300 square feet of wool for a Sprinter 144, according to The Wayward Home. Using those areas:
| Approach (walls and ceiling, high-roof mid-length van) | Area used | Estimated weight |
|---|---|---|
| Thinsulate SM600L | 225 sq ft | about 32 lb |
| Havelock wool R7 | 300 sq ft | about 60 lb |
| 1 in polyiso, cut between ribs | 225 sq ft (7 to 8 sheets) | about 38 to 49 lb, plus can foam |
| Closed-cell spray foam, 1 in | 225 sq ft | about 33 lb |
| Closed-cell spray foam, 2 in | 225 sq ft | about 66 lb |
| Butyl sound deadener, 50 sq ft | 50 sq ft | about 35 lb |
All weights are our estimates from the per-area figures above. None is huge alone, but it stacks on top of plywood, furring and cabinets. If payload is tight, the materials and payload guide walks through the full math.
Note the sound deadener line: butyl mat at roughly 0.7 lb per square foot (Noico 80 mil listings) is the heaviest material here per square foot. Bearfoot Theory's van guide notes that about 50 square feet covers the major panels of a panel van.
Cost per van in 2026
These are prices from current retailer listings checked in November 2026, for a high-roof mid-length van (walls, ceiling and doors only; the floor is separate). Prices change by seller, roll length and shipping, so treat ranges as a guide and check current listings.
| Approach | Quantity | Price basis | Material cost |
|---|---|---|---|
| Thinsulate SM600L, cut from roll | 40 to 45 linear ft | $7.39 to $12.45 per linear ft (Keiproject, AVC Rig, Second Skin, Campervan HQ listings) | about $300 to $560 |
| Thinsulate pre-cut van kit | one kit | about $630 to $845 (Campervan HQ and Sprinter Store listings) | about $630 to $845 |
| Havelock wool | 3 boxes (300 sq ft) | $150 per R7 box, $200 per R8 box (Havelock listings) | about $450 to $600, plus shipping |
| 1 in polyiso board | 7 to 8 sheets | about $29 per JM AP Foil sheet (retailer listing) | about $205 to $235, plus foil tape and can foam |
| DIY closed-cell spray foam | 2 Froth-Pak 200 kits (estimate) | $379 to $580 per kit (retailer listings) | about $760 to $1,160 |
| Professional closed-cell spray foam | full van, 2 in | from $1,950 (Retrofoam of Michigan, starting price) | from about $1,950 |
| Floor: 1 in XPS | 2 to 3 sheets | $26 to $32 per Foamular 150 sheet | about $55 to $95 |
Why two spray foam kits? Gary Reysa's ProMaster build on BuildItSolar used a 200 board-foot kit (rated for 200 square feet at 1 inch) and got about 170 square feet at an average of only three-quarters of an inch, then ran out before finishing the doors. A Lowe's reviewer reported a similar shortfall. Plan on more than the label says.
For context on where insulation sits in the overall budget, see how much a van conversion costs in 2026.
How much interior width each approach costs
The key idea: insulation that lives inside the rib cavities costs you no width at all. What costs width is everything that sits proud of the ribs: furring strips, a continuous foam layer, and the wall panel itself.
Thinsulate (about 1.65 inches) and 2-inch wool batts are soft, so they conform to the cavity behind the panel. Rigid board cannot follow the curve of a van wall, so it is usually cut into pieces between ribs, or laid as a continuous layer over the ribs as a thermal break. Spray foam fills the cavity and then has to be trimmed flush, or it pushes your panels inward.
The table below is our estimate per side, using common stack-ups: a 1/4-inch plywood panel fastened straight to the ribs with rivnuts, or the same panel on 3/4-inch furring strips.
| Wall approach | Added per side (panel on ribs) | Added per side (on 3/4 in furring) | Total width lost |
|---|---|---|---|
| Thinsulate in cavities | about 0.25 in | about 1 in | about 0.5 to 2 in |
| Wool in cavities | about 0.25 in | about 1 in | about 0.5 to 2 in |
| Foam board cut between ribs | about 0.25 in | about 1 in | about 0.5 to 2 in |
| Foam board continuous over ribs (1 in) | about 1.25 in | about 2 in | about 2.5 to 4 in |
| Spray foam trimmed flush | about 0.25 in | about 1 in | about 0.5 to 2 in |
| Spray foam left proud (0.5 to 1 in) | about 0.75 to 1.25 in | about 1.5 to 2 in | about 1.5 to 4 in |
Two inches sounds trivial until you are fitting a sideways bed. The three common vans already differ inside, as the Sprinter vs Transit vs ProMaster dimension comparison shows, and if a crosswise bed is the plan, every half inch of wall stack matters. Furring strips are usually the first thing worth reconsidering.
Install difficulty and time
Thinsulate is the easiest. You cut it with scissors, spray the metal with a high-tack adhesive such as 3M 90 spray adhesive, and press it in. It can be pulled back out later to run a wire or fix a dent. Far Out Ride's key warning is that it "must be uncompressed to be effective", so do not jam it in behind tight panels. Stuffing scraps into pillars with a dowel or a strip of wood covers the hard-to-reach spots.
Wool is a little slower. The Wayward Home reports that it took one person several days for a Sprinter 144, and suggests two people could finish in a couple of days. Large flat panels need tape or string to hold the batts, installation sheds fibres (wear a mask), and fresh wool can smell faintly like a barn for a while. Havelock's batts are treated with boric acid against insects.
Foam board is cheap and fast on the floor, where it lies flat between sleepers under the subfloor. On walls it is fiddly: lots of small pieces, cut to fit between ribs, then every edge sealed with foil HVAC tape and low-expansion can foam. Skip the sealing and you have created exactly the air gaps that hold condensation.
Spray foam is the hardest to do well yourself. Reysa's notes are a good reality check: apply several thin passes rather than one thick one, keep the kit and the van at the right temperature, mask everything because overspray goes everywhere, change nozzles if you stop spraying for more than about 30 seconds, and leave channels for wiring and plumbing. Two-part foam releases chemicals while it cures, so follow the manufacturer's safety data sheet on respirators, skin protection and ventilation to the letter. If in doubt, a professional installer with van experience is the safer route.
Whatever you choose, the electrical runs should go in before the walls close, with conduit or pull strings so you can add circuits later. Keep insulation clear of anything the manufacturer says needs airflow, and follow your heater and appliance manuals for clearances. The electrical sizing guide covers the planning side.
Sound deadening: a separate job
Insulation and sound deadening are related but not the same.
- Butyl damping mat (the Dynamat, Kilmat, Noico family) goes directly on bare metal and stops large panels from drumming. Vansmith calls it the budget-friendly first step for road noise. You do not need full coverage: tap each panel and add 80 mil butyl sound deadening mat near the centre until it thuds instead of rings. A hard sound deadener roller makes it bond properly.
- Fibrous fill (Thinsulate, wool) absorbs airborne noise in the cavity. Thinsulate SM600L is sold as an acoustic product first; that is where the "acoustic" in its name comes from.
- Mass loaded vinyl blocks airborne noise but is heavy, so Vansmith suggests saving it for floors and walls where quiet really matters and checking it against your payload.
Vansmith singles out the wheel wells, rear doors and sliding-door area for extra attention, so if you only have a little mat, start there.
Reflectix, radiant barriers and the Arizona question
Builders are consistent about Reflectix: as a stand-alone wall insulation it is weak (Far Out Ride lists it at about R1 for the whole product), and the reflective face only helps if it faces an air gap. Pressed flat against metal, it is mostly a thin foam layer. Some builders use it, or a thin closed-cell foam sheet such as closed-cell foam thermal break, over the ribs as a thermal break behind the panel, which is a reasonable job for it.
In a hot desert climate, the sun on the roof, walls and glass is the enemy. The Wayward Home reports roughly a 30-degree difference between bare metal and insulated, panelled areas in sun, which is a good illustration of why every exposed square foot of steel matters. Insulation slows heat gain; it does not remove heat. For Arizona summers the bigger levers are window covers, ventilation and, if you have the power for it, air conditioning. The heating and cooling guide goes into what actually works here.
What experienced builders recommend, and regret
Pulling together build walkthroughs, forum threads and Reddit discussions:
- Thinsulate walls and ceiling, XPS floor is the most common mixed-climate recommendation. Far Out Ride uses exactly that, and rejected spray foam because it is permanent and some body shops will not repair panels that have it.
- Wool fans are loyal. In a r/vandwellers insulation comparison thread, wool drew the most enthusiasm, for warmth per inch and moisture buffering, though its thermal edge over Thinsulate was disputed in the same thread. The caveats are mess, weight and shipping; a commenter on The Wayward Home's post said shipping cost about as much as the wool.
- Spray foam splits people. Reysa found his foamed ProMaster somewhat quieter after a short drive. The regrets are rust found later behind foam, thin patchy DIY coverage, and wiring or dents that are hard to reach afterward.
- Fiberglass and denim are rejected by Far Out Ride and others because both hold moisture. Rockwool divides people.
- Reflectix as the main wall insulation shows up on most lists of beginner mistakes.
For more patterns like these across the whole build, see the van build mistakes owners say they would never repeat.
A simple decision guide
- Mostly warm or mixed climates, want it done once: Thinsulate walls and ceiling, 1-inch XPS floor, butyl mat on big panels. Breathable, light, removable.
- Want a bit more warmth and a natural product: wool in walls and ceiling, XPS floor. Budget for shipping and a messier weekend.
- Lowest cost, willing to be meticulous: polyiso or XPS cut between ribs, every seam taped and foamed, Thinsulate scraps in the pillars.
- Serious cold-weather use and a professional installer: closed-cell spray foam over clean, treated steel, drain holes kept open, wiring channels left clear.
For any of these, an infrared thermometer finds cold spots and thermal bridges once the walls are closed, and the hygrometer shows whether condensation is under control.
FAQ
Do I need a vapour barrier in a van?
It depends on the strategy. With breathable fill like Thinsulate or wool, many experienced builders skip a plastic vapour barrier so the wall can dry. With a sealed strategy (spray foam or fully taped foam board), the foam itself is the barrier. The thing to avoid is mixing a partial barrier with breathable fill, which can trap water.
Is Thinsulate actually warmer than wool?
Not per inch, on published numbers. Havelock lists wool at R3.6 per inch; Far Out Ride lists Thinsulate SM600L at about R3.3. The real-world difference is small next to thermal bridging through the ribs and heat loss through windows.
Will spray foam rust my van?
Closed-cell spray foam applied over clean, dry, treated steel, with drain holes kept open, is used in many vans without problems. The rust stories involve trapped condensation behind foam that pulled away, open-cell foam, or foam sprayed over existing rust.
How much insulation do I need for a Sprinter 144 high roof?
Campervan HQ suggests about 40 to 45 linear feet of 60-inch Thinsulate for walls, ceiling and doors. Havelock has recommended around 300 square feet of wool for the same van. Add separate foam board for the floor.
Should I insulate the floor?
Yes, for most builds. One inch of XPS between sleepers under the subfloor is the common choice because it is cheap, flat and keeps its R-value better than polyiso in the cold.
Does insulation help in Arizona summer heat?
It slows heat gain through the walls and roof, which helps an air conditioner or fan keep up, but it cannot cool the van by itself. Window covers and ventilation matter as much as the insulation.
Some links are Amazon affiliate links. As an Amazon Associate we earn from qualifying purchases, at no extra cost to you.